Avaya IP403 Office Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 115

Avaya IP403 Office Скачать руководство пользователя страница 8

IP Office Installation

Installation Manual

Page 2

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

Scope of Manual

This manual, for Avaya IP Office systems, covers the following subjects and should be read in the
sequence shown below:

•

Avaya IP Office Platforms

This section provides details of the various Avaya IP Office platforms available. Illustrations of the
front and rear of each unit show what ports/sockets/etc are provided. Typical configuration
examples are also provided in this section. A further section details the country variants of
modules/trunks/integral modules/etc.

•

Preparing for and Installing a new system

These sections provide all the information required and the actions to be performed to physically
install an IP Office, i.e. what tools are required, the environmental/power requirements, wall
mounting, rack mounting, etc. The software installation is covered in the following section.

•

Basic System Programming

System programming is necessary for configuration and maintenance of the Avaya IP Office.
This manual only covers the installation of the IP Office suite of programs. For full details refer to
the Installation Wizard Help files and/or to the Manuals contained on the documentation CD
(supplied with every unit).

•

Terminal/Telephone Installation

This manual details the information required to install telephone but does not detail the usage
and functionality of IP Office terminals/telephones. These details are to be found in the
appropriate User Guides

.

The terminals/telephones that are supported by the IP Office are (these

are also used across a number of Avaya platforms:

•

Avaya 2000 Series: 20AT, 20CC, 2010, 2030, 2050, 20DSS/BLF and 20DT.

•

Avaya 2400 Series: 2420.

•

Avaya 3600 Series: 3616, 3626.

•

Avaya 4400 Series: 4406D, 4412D, 4424D and 4450DSS*.

•

Avaya 4600 Series: 4602, 4602SW, 4620, 4606, 4612 and 4624.

•

Avaya 6400 Series: 6408D+, 6416D+M, 6424D+M and XM24 (DSS).

•

*Caution:

See

DT Line Cord for Structured Cabling

for wiring details on a

4450DSS module.

•

Safety and Homologation Statements

This provides all the necessary Safety, Homologation Statements and Regulatory Instructions for
Use required. This section also detail where further information, including other Manuals and
support telephone numbers, can be obtained

•

Technical Data

This manual contains information on the Port Pinouts/Safety classifications, cables, and basic
technical specifications only (see Technical Specifications). Descriptions of the functionality,
features and performance of the IP Office are covered by the Product Description.

«
...
6
7
8
9
10
...
»

Содержание IP403 Office




















































































































Отзывы:

Нет отзывов