manualshive.com logo in svg

Avaya IP403 Office, Руководство по установке, Страница: 78 / 115

Поделиться
Скачать
Avaya IP403 Office Скачать руководство пользователя страница 78

IP Office Installation 

Installation Manual 

Page 72 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Electromagnetic Interference Information 

Federal Communications Commission (FCC)  

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference, in which case the user will be 
required to correct the interference at his or her own expense.  

 

Canadian Department of Communications (DOC) 

''NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical 
Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration 
number signifies that registration was performed based on a Declaration of Conformity indicating that 
Industry Canada technical specifications were met. It does not imply that Industry Canada approved the 
equipment."  

 

Содержание IP403 Office




















































































































Отзывы:

Нет отзывов