manualshive.com logo in svg

Avaya IP403 Office, Руководство по установке, Страница: 4 / 115

Поделиться
Скачать
Avaya IP403 Office Скачать руководство пользователя страница 4

Table Of Contents 

Installation Manual 

Page ii 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Out of Building Telephone Installations ............................................................................................... 45

 

Rack Mounting Barrier Boxes .............................................................................................................. 46

 

Installing a New System .......................................................................................................... 49

 

Unpacking................................................................................................................................................. 49

 

Trunk Interface Modules (BRI/PRI/ANALOG4) ........................................................................................ 50

 

Installation of Voice Compression Modules (VCM) .................................................................................. 51

 

Dual Modem Module ................................................................................................................................ 52

 

Rack Mounting Assembly Instructions...................................................................................................... 53

 

IP401 Expansion and Installation of Integral Modules.............................................................................. 54

 

IP401 Compact Office Wall Mounting....................................................................................................... 55

 

Initial Assembly......................................................................................................................................... 56

 

Basic System Programming ................................................................................................... 57

 

Introduction............................................................................................................................................... 57

 

Programming Tools .................................................................................................................................. 58

 

Programming Tools.............................................................................................................................. 58

 

PC to IP Office LAN Port Connection .................................................................................................. 58

 

Initial Programming................................................................................................................................... 59

 

Initial Programming .............................................................................................................................. 59

 

Using the IP Office Installation Wizard:................................................................................................ 60

 

Using the IP Office Manager Application: ............................................................................................ 60

 

Software Upgrades................................................................................................................................... 61

 

Software Upgrades .............................................................................................................................. 61

 

Upgrading an IP403 to Software Level 2.1 .......................................................................................... 63

 

Telephone Installation ............................................................................................................. 65

 

Checking Telephones............................................................................................................................... 65

 

Checking Telephones .......................................................................................................................... 65

 

Connecting & Testing IP Office Telephones ........................................................................................ 65

 

Connecting & Checking Two-Wire Telephones ................................................................................... 66

 

Power Fail Telephones and Sockets ................................................................................................... 66

 

Wall Mounting 2000 Series Telephones................................................................................................... 67

 

Wall Mounting 44/4600, 2420 & 6400 Series Telephones ....................................................................... 68

 

System Handover..................................................................................................................... 69

 

Checklist ................................................................................................................................................... 69

 

Safety and Homologation Statements.................................................................................... 71

 

Safety and Homologation Statements ...................................................................................................... 71

 

Lithium Batteries....................................................................................................................................... 71

 

Lightning Protection/Hazard Symbols ...................................................................................................... 71

 

Electromagnetic Interference Information................................................................................................. 72

 

Federal Communications Commission (FCC) ..................................................................................... 72

 

Canadian Department of Communications (DOC)............................................................................... 72

 

Trunk Interface Modules........................................................................................................................... 73

 

USA/Canada ........................................................................................................................................ 73

 

Rest Of World (ROW) .......................................................................................................................... 73

 

Further Information and Product Updates ................................................................................................ 74

 

Further Information and Product Updates............................................................................................ 74

 

Support Telephone Numbers............................................................................................................... 74

 

Regulatory Instructions for Use ................................................................................................................ 75

 

Regulatory Instructions for Use............................................................................................................ 75

 

IP Office Operation in Australia............................................................................................................ 75

 

Industry Canada Notification (DoC) ..................................................................................................... 76

 

IP Office Operation in EU..................................................................................................................... 76

 

IP Office Operation in New Zealand .................................................................................................... 76

 

IP Office Operation in USA .................................................................................................................. 77

 

Technical Data.......................................................................................................................... 79

 

Port Pinouts .............................................................................................................................................. 79

 

Содержание IP403 Office




















































































































Отзывы:

Нет отзывов