manualshive.com logo in svg

Avaya IP403 Office, Руководство по установке, Страница: 77 / 115

Поделиться
Скачать
Avaya IP403 Office Скачать руководство пользователя страница 77

 

Installation Manual 

Page 71 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Safety and Homologation Statements 

Safety and Homologation Statements 

CE Mark

 

The "CE" mark affixed to this equipment means that the unit complies with the 1999/5/EC (R&TTE), 
89/336/EEC (EMC) and 72/23EEC (LVD) Directives 

 

Declaration of Conformity 

The Declaration of Conformity (DoC) for the IP400 Office products is contained with in the CD 
accompanying the products. 

This warning symbol is found on the base of IP401, IP403, IP416 and IP412 units and on the base of the 
IP400 Digital Station 80W Lump-in-Line PSU (see 

IP400 Digital Stations 16/30

). Refer to 

Trunk Interface 

Modules

 for information concerning which Trunk Interface module variants are fitted in which country. 

• 

WARNING  
The Avaya IP400 Office units are intended to be installed by 'Service Personnel' and it is 
the responsibility of the Service Personnel to ensure that all subsidiary interconnected 
equipment is wired correctly and also meet the safety requirements of IEC60950 or 
UL60950 where applicable. 

 

Lithium Batteries 

A lithium battery is fitted to the real time clock on the IP401/403/406 and IP412 mother boards. 

• 

WARNING  
The Lithium battery must only be replaced by Avaya personnel or authorized 
representatives. There is a danger of explosion if the battery is incorrectly replaced. 
Replace only with the same or equivalent type recommended by the manufacturer. 
Dispose of used batteries according to the manufacturer's instructions. 

 

Lightning Protection/Hazard Symbols 

Lightning protectors 

 

The buildings lightning protectors 

must be verified

 as follow: 

1.  Check the lightning protectors, at the trunk cable entry point to the building housing the Avaya IP 

Office, paying special attention to the lightning protection grounding. Report any problems, in 
writing, to the telephone company. 

2.  Equipment that is designed to be connected using internal wiring is typically 

not

 lightning 

protected. Hence, Avaya IP Office extension cabling 

must not leave the building.

 For 

installations where telephones and/or other standard (tip/ring) devices are installed in another 
building then lightning protection is required (see 

Out of Building Telephone Installations

). 

Hazard Symbol  

The shock hazard symbol is intended to alert personnel to electrical hazard or equipment damage. The 
following precautions must also be observed when installing telephone equipment:

 

1. 

Never install

 telephone wiring during a lightning storm. 

2. 

Never install

 telephone jacks in wet locations unless the jack is specifically designed for wet 

locations. 

3. 

Never Touch

 uninsulated telephone wires or terminals unless the telephone line has been 

disconnected at the network interface. 

4.  Always use caution when working with telephone lines. 

Содержание IP403 Office




















































































































Отзывы:

Нет отзывов