Avaya IP403 Office Скачать руководство пользователя страница 35

Страница: 35 / 115

Expansion Modules

Installation Manual

Page 29

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

IP400 So8

The So8 Module is only applicable to countries that support the ETSI signaling protocol (see

Expansion

Modules

•

BRI Ports

These are 64k ISDN BRI S-Bus ports and are used for connection to ISDN Telephones, Group 4
faxes, Video conferencing units, etc.

WARNING:

BRI phone ports must not be connected to the external ISDN Connections.

•

Expansion Port

Used to connect a So8 Module to the Expansion Ports of an IP Office platform.

•

DC Power I/P Socket

Socket for the external 24V DC unregulated power supply (supplied with kit).

•

DTE Port

A 25-way D-type socket. Used for connection to PC (as a diagnostic aid).

IP400 So8 is supplied with one blue Expansion Interconnect cable.

Содержание IP403 Office




















































































































Результаты поиска

Содержание IP403 Office

Отзывы:

Avaya IP403 Office, Руководство по установке, Страница: 35 / 115

Результаты поиска

Содержание IP403 Office

Отзывы: