Avaya IP403 Office Скачать руководство пользователя страница 107

Страница: 107 / 115

Installation Manual

Page 101

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

SNMP

SNMP Functionality

The IP Office SNMP Agent implements SNMPv1 on a read-only basis for security reasons.

•

SNMP Agent Configuration

•

MIBs Supported

•

Trap Generation

•

MIB Loading

•

HP OpenView Network Node Manager 6.41 and earlier

•

CastleRock SNMPc 5.1.6c and earlier

SNMP Agent Configuration

The following operational items may be configured for the IP Office SNMP Agent using the IP Office
Manager:

SNMP Server:

•

Enable/disable

•

Enabled: the device to respond to SNMP requests and send traps for any associated
events that occur if so configured.

•

Disabled: the SNMP agent on the device does not respond to SNMP requests or send
traps.

•

UDP Port (default 161)

•

Changes the default port value of the SNMP Agent.

•

Read-only community

•

Community string of up to 32 alphanumeric characters for read-only access.

•

Two trap destinations:

•

IP Address

•

UDP Port (default 162)

•

Community string of up to 32 alphanumeric characters.

•

Event mask specifying the events the trap destination is interested in receiving

•

generic (coldStart, warmStart, linkDown, linkUp, authenticationFailure)

•

licence – License Key Server access fault notifications

•

phone change – connected phone change notification

Содержание IP403 Office




















































































































Результаты поиска

Содержание IP403 Office

Отзывы:

Avaya IP403 Office, Руководство по установке, Страница: 107 / 115

Результаты поиска

Содержание IP403 Office

Отзывы: