Avaya IP403 Office Скачать руководство пользователя страница 11

Страница: 11 / 115

Installation Manual

Page 5

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

IP401 Compact Office Platform

IP401 Compact Office

The IP401 Compact Office system platform is supplied in two variants:

•

IP401 Compact Office 2 supports:

Two digital and two analog telephones A BRI ISDN port (2

trunks) An four port auto-negotiating 10/100 BaseT LAN hub.

•

IP401 Compact Office 4 supports:

Four digital and four analog telephones Two BRI ISDN

ports (4 trunks) An eight port auto-negotiating 10/100 BaseT LAN hub. The IP401 Compact
Office 2 can be expanded to an IP401 Compact Office 4.

See

IP400 Office Systems

for country specific variants.

The auto-negotiating 10/100 BaseT LAN hub provides access to networks and/or up to eight IP
telephones.

The DT ports support Avaya 2000 series telephones. DT ports are set to A-Law PCM encoding at default
but can be programmed to -Law PCM encoding.

In addition the IP401 Compact Office can be fitted with any of the following optional Integral Modules:

•

WAN Port

This port supports a single synchronous data connection, which can be X.21, V.35 or V.24.

•

Voice Compression Module (VCM5)

Supports VoIP applications (over two of the five channels) using Avaya 4600 IP telephones
connected via LAN ports.

•

VME card

Provides memory capacity for embedded voice mail feature.

Содержание IP403 Office




















































































































Результаты поиска

Содержание IP403 Office

Отзывы:

Avaya IP403 Office, Руководство по установке, Страница: 11 / 115

Результаты поиска

Содержание IP403 Office

Отзывы: