Avaya IP403 Office Скачать руководство пользователя страница 46

Страница: 46 / 115

IP Office Installation

Installation Manual

Page 40

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

Space requirements

Check that the planned location meets the following requirements.

•

Height :

•

A IP401 Compact Office module is 71mm (2.8 inches) high.

•

IP403, 406, 412 and all Expansion modules are 71mm(2.8 inches) high. Hence the total
height of a system is the number of modules multiplied by 71mm (2.8 inches).

•

Width :

•

A IP401 Compact Office module is 255mm (10 inches) wide.

•

IP403, 406, 412 and all Expansion modules are 445mm (17.5 inches) wide.

•

Depth :

•

A IP401 Compact Office module is 235mm (9.3 inches) deep.

•

IP403, 406, 412 and all Expansion modules are 245mm (9.7 inches) deep.

•

IP403, IP406, IP412 and Expansion modules can be mounted in 19" racks (see

Rack

Mounting Assembly Instructions

•

When modules are free standing (ideally mounted one upon another), allow a
minimum clearance of 50mm (20 inches) either side for cable trunking.

•

Check there is suitable lighting for installation, system programming and future
maintenance.

•

Check that there is sufficient working space for installation and future maintenance.

•

Ensure that likely activities near the system will not cause any problems, e.g. access
to and maintenance of any other equipment in the area.

Содержание IP403 Office




















































































































Результаты поиска

Содержание IP403 Office

Отзывы:

Avaya IP403 Office, Руководство по установке, Страница: 46 / 115

Результаты поиска

Содержание IP403 Office

Отзывы: