Avaya IP403 Office Скачать руководство пользователя страница 105

Страница: 105 / 115

Technical Data

Installation Manual

Page 99

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

Protocols

Protocol

Information

A-Law

- - -

PCM encoding (mainly used outside North America)

U-Law

- - -

PCM encoding (mainly used in North America and Japan)

V.120

- - -

A standard Rate Adaption mechanism.

V.110

- - -

A standard Rate Adaption mechanism.

PPP

RFC 1661

Point to Point Protocol.

LCP

RFC 1570

Link Control Protocol.

RFC 1990

Multi-Link (Point to Point) Protocol.

PAP

RFC 1334

Password Authentication Protocol.

CHAP

RFC 1994

Challenge Handshake Authentication Protocol.

CCP

RFC 1962

Compression Control Protocol.

STAC

RFC 1974

Stac LZS Compression Protocol.

MPPC

RFC 2118

Microsoft Point to Point Compression (Protocol).

BACP

RFC 2125

Bandwidth Allocation Control Protocol.

IPCP

RFC 1332

Internet protocol Control Protocol.

TCP/IP

RFC 793

Transmission Control Protocol/Internet Protocol.

DHCP

RFC 1533

Dynamic Host Control Protocol.

NAT

RFC 1631

Network Address Translation.

BOOTP

RFC 951

Bootstrap Protocol.

SNMPv1

RFC1157 (STD15)

RFC1155 (STD16)

RFC1212 (STD16)

RFC1215

Simple Network Management Protocol

Structure and Identification of Management Information for TCP/IP-
based internets

Concise MIB Definitions

A Convention for Defining Traps for use with the SNMP

MIB-II

RFC1213 (STD17)

Management Information Base for Network Management of TCP/IP-
based internets:MIB-II

RIP

RFC1058

RFC2453

RFC1722 (STD57)

Routing Information Protocol

(STD56) RIP Version 2

RIP Version 2 Protocol Applicability Statement

IPSEC

RFC2401

RFC2402

RFC2403

RFC2404

RFC2405

RFC2406

RFC2407

RFC2408

RFC2409

RFC2410

RFC2411

Security Architecture for the Internet Protocol

IP Authentication Header

The Use of HMAC-MD5-96 within ESP and AH

The Use of HMAC-SHA-1-96 within ESP and AH

The ESP DES-CBC Cipher Algorithm With Explicit IV

IP Encapsulating Security Payload (ESP)

The Internet IP Security Domain of Interpretation for ISAKMP.

Internet Security Association and Key Management Protocol

The Internet Key Exchange (IKE).

The NULL Encryption Algorithm and Its Use With IPsec.

IP Security Document Roadmap.

L2TP

RFC2661

RFC3193

Layer Two Tunneling Protocol "L2TP"

Securing L2TP using IPsec

ENTITY MIB

RFC2737

Entity MIB (Version 2)

TFTP

RFC1350

Trivial File Transfer Protocol

NTP

RFC868

Network Time Protocol

Содержание IP403 Office




















































































































Результаты поиска

Содержание IP403 Office

Отзывы:

Avaya IP403 Office, Руководство по установке, Страница: 105 / 115

Результаты поиска

Содержание IP403 Office

Отзывы: