manualshive.com logo in svg

Avaya IP403 Office, Руководство по установке, Страница: 81 / 115

Поделиться
Скачать
Avaya IP403 Office Скачать руководство пользователя страница 81

Safety and Homologation Statements 

Installation Manual 

Page 75 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Regulatory Instructions for Use 

Regulatory Instructions for Use 

Any changes or modifications not expressly approved by Avaya ECS Ltd could void the user's authority 
to operate the equipment.  

• 

IP Office Operation in Australia

 

• 

IP Office Operation in Canada

 

• 

IP Office Operation in EU

 

• 

IP Office Operation in New Zealand

 

• 

IP Office Operation in USA

 

 

IP Office Operation in Australia 

Connection 

Connection of IP400 Office products must be via a Line Isolation Unit with a telecommunications 
compliance label. 

 

BRI Interface 

During the configuration, ensure "000" emergency number is not barred, by performing the following: 

• 

Short Code: "000" Telephone No.: "000;" Function: "Dial Emergency" 

 

Connections to TS013, the following Bearer Capabilities shall not be used: 

• 

7kHz Audio Video Restricted Digital Information 

 

If unknown type of number is used in calling party number, the network will use the default CLI. 

The system must be configured for Point to Multi point connection to comply with Austel requirements for 
connecting to TS013 circuits. 

As the IP Office does not support emergency dialing after loss of power, the following warning notice 
should be recognized: 

• 

WARNING

 

This equipment will be inoperable when mains power fails. 

 

PRI Interface 

During the configuration, ensure "000" emergency number is not barred, by performing the following: 

• 

Short Code: "000" Telephone No.: "000;" Function: "Dial Emergency" 

 

WARNING 

This equipment will be inoperable during mains power failure. 

Содержание IP403 Office




















































































































Отзывы:

Нет отзывов