Avaya IP403 Office Скачать руководство пользователя страница 47

Страница: 47 / 115

Preparing for Installation

Installation Manual

Page 41

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

Environmental requirements

The planned location must meet the following requirements:

•

Check that the area is a well ventilated area, having a temperature range of 0

C to +40

C and a

humidity range of 10% to 95% non-condensing.

•

Check there are no flammable materials in the area.

•

Check there is no possibility of flooding.

•

Check that no other machinery or equipment needs to be moved first.

•

Check that it is not an excessively dusty atmosphere.

•

Check that the area is unlikely to suffer rapid changes in temperature and humidity.

•

Check for the proximity of strong magnetic fields, sources of radio frequency and other electrical
interference.

•

Check there are no corrosive chemicals or gasses.

•

Check there is no excessive vibration or potential of excessive vibration, especially of the cabinet
mounting surface.

•

Check that, for the USA only, where telephones are installed in another building, that the
appropriate IROB protectors are fitted (see

Out of Building Telephone Installation

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of fire, electric shock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or

laundry tub, in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a

fire. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS.

Содержание IP403 Office




















































































































Результаты поиска

Содержание IP403 Office

Отзывы:

Avaya IP403 Office, Руководство по установке, Страница: 47 / 115

Результаты поиска

Содержание IP403 Office

Отзывы: