manualshive.com logo in svg

Avaya IP403 Office, Руководство по установке, Страница: 62 / 115

Поделиться
Скачать
Avaya IP403 Office Скачать руководство пользователя страница 62

IP Office Installation 

Installation Manual 

Page 56 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Initial Assembly 

Prior to initial assembly and mounting (rack or free standing) of your system, check that: 

• 

For Analog Trunk 16 expansion modules, ensure that the protective ground is fitted. 

• 

The required Trunk Interface Modules have been installed, are of the correct country variant type 
and if functional grounding is required, that it has been fitted. 

• 

Any optional Integral Voice Compression and/or Dual Modem Modules have been fitted. 

• 

Where rack mounting is required, that the mounting brackets have been fitted. 

• 

Where structured cabling is to be used it has been installed, conforms to all local regulations and 
is clearly labeled. 

 

Perform the following: 

1.  Mount the IP Office modules in their final location (free standing units are ideally stacked one 

upon another). 

2.  Run the individual Lump-in-Line PSU cables back to the switchable mains supply but 

do not 

switch-on

 

or connect

 the PSUs to the IP Office modules. 

3.  With the exception of a WAN3 module, connect the IP Office Control Unit to the Expansion 

Modules using Expansion Interconnect Cables (blue). These cables run from one of the 
Expansion Ports on the rear of a base module to the Expansion Port on the rear of the Expansion 
Modules. For WAN3 Modules, use a LAN Interconnect cable (403, 406) or LAN crossover cable 
(412) running between one of the LAN Ports on the front of the control unit to the LAN Port on the 
front of the WAN3 module. 

4.  Connect the Trunk Ports on the control unit, using PRI/BRI CAT5E cables, to your provider's 

trunk sockets. 

5.  Connect the DT/DS/POT Ports on the front of the units, using DT Line Cords, to the structured 

cable sockets. Note that in default, the lowest port number corresponds to the lowest extension 
number (201). 

6.  Install all telephones in their appropriate locations.  

7.  Connect your PC LAN Port to one of the LAN Ports on the front of an IP Office base module 

using a LAN Cable. 

8.  Connect the individual Lump-in-Line PSU to each IP Office module and switch on. 

• 

IMPORTANT

 

Power on the Expansion Modules first. If the main IP Office Module does not detect an 
item at power on, it will not use it. If power is switched on from a central point for all 
modules, then, as the main unit is the slowest to start, this will be taken care of 
automatically.

 

9.  From the IP Office Administrator CD, install on your PC the software required to configure and 

manage your Avaya IP Office.  

10. Proceed to 

IP401 Expansion and Installation of Integral Modules

 below. 

 

  

Содержание IP403 Office




















































































































Отзывы:

Нет отзывов