Avaya IP Ofice 8.0 Скачать руководство пользователя

Страница: 65 / 256

IP Office Basic Edition - Quick Mode Installation

Page 65

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

IP500 V2 Installation: IP500 Card Installation

4.4.3 IP500 Card Insertion

Having prepared each IP500 base card by adding any

trunk daughter card

, the base card can be inserted into the

control unit.

Warnings

Correct anti-static protection steps should be taken while handling circuit boards.

Cards must never be added or removed from the control unit while it has power connected.

Tools Required

5mm Flat-blade screwdriver.

Anti-static wrist strap and ground point.

Installing an IP500 Card

1. Check that there is no power to the control unit.

2. Using a flat-bladed screwdriver, remove the cover from the slot on the front of the control unit that will be used for

each card being installed. This cover is no longer required but should be retained until installation has been
completed.

3. Allowing the card to rest against the bottom of the slot, begin sliding it into the control unit. When half inserted,

check that the card rails have engaged with the slot edges by trying to gently rotate it. If the card rotates remove it
and begin inserting it again.

4. The card should slide in freely until almost fully inserted. At this point apply pressure at the base of the front of the

card to complete insertion.

5. Using a flat-bladed screwdriver secure the card.

Содержание IP Ofice 8.0

































































































































































































































































Результаты поиска

Содержание IP Ofice 8.0

Отзывы:

Похожие инструкции для IP Ofice 8.0

Бренды по названию

Популярные бренды

Avaya IP Ofice 8.0, Быстрая установка

Результаты поиска

Содержание IP Ofice 8.0

Отзывы:

Похожие инструкции для IP Ofice 8.0

Бренды по названию

Популярные бренды