Avaya IP Ofice 8.0 Скачать руководство пользователя | Manualshive

Страница: 78 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 78

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

4.11 Connecting Phones

During initial power up, the IP Office automatically creates extension and user entries for all analog and digital extension
ports (DS and TCM) in the system. This allows those devices to be connected without any additional programming.

·

!

Warning

If the system has been upgraded from a previous release of IP Office software, all phones will be restricted from
making any calls until a

system upgrade license

has been entered. The dialing restriction includes not being able

to make emergency calls.

·

This section does not cover the installation of DECT, H323 and SIP telephones. For installation of those devices
refer to the appropriate supplementary installation manuals.

4.11.1 Analog Phones

Connect any analog phones to their appropriate

Phone

ports. Ensure that those connected to

power failure ports

are clearly labeled as such.

4.11.2 ETR Phones

Connect any ETR phones to their appropriate

ETR

ports. These phones do not need to load additional firmware.

4.11.3 DS Phones

Connect any digital phones to their appropriate

DS

ports. These phones may need to upgrade their firmware to match

that supported by the IP Office core software. The appropriate firmware is supplied with the IP Office Manager software
and copied onto the System SD card for IP500 V2 systems.

The phones will automatically load the firmware from the IP Office system if necessary.

·

The upgrade process takes approximately 10 minutes during which time the phone will display a warning. The
phone should not be disconnected during this process.

·

Due to memory requirement, only 10 phones of the same type can be upgraded at a time. Starting from the first
port needing to be upgraded, the IP Office will upgrade all connected phones of the same type needing upgrading in
batches. It will then upgrade the next connected type of phones needing to be upgraded.

·

Once the phone connected to a port has been upgraded, the IP Office will not check whether the phone on that port
needs to be upgraded again except following a system reboot, i.e. multiple phones cannot be upgraded by
swapping the connected phones on the same.

235

230

37

226

224

«
...
76
77
78
79
80
...
»

Содержание IP Ofice 8.0

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IP Ofice 8.0

SCH-i600 Series

Бренд: Samsung Страницы: 12

SGH-t329 Series

Бренд: Samsung Страницы: 143

Бренд: Camrivox Страницы: 4

Бренд: Panasonic Страницы: 45

Бренд: G53 Limited Страницы: 10

Бренд: Sony Ericsson Страницы: 19

Бренд: Icemobile Страницы: 20

Бренд: Blu Страницы: 31

Бренд: PCD Страницы: 16

Moment SPH-M900

Бренд: Samsung Страницы: 122

My Shot SCH-r430 series

Бренд: Samsung Страницы: 142

Mesmerize SCH-I500

Бренд: Samsung Страницы: 170

Messager SCH-r450 Series

Бренд: Samsung Страницы: 150

MYTHIC SGH-A897 Series

Бренд: Samsung Страницы: 202

Messager Touch SCH-R631

Бренд: Samsung Страницы: 165

MYTHIC SGH-A897 Series

Бренд: Samsung Страницы: 202

M620 - SPH UpStage Cell Phone

Бренд: Samsung Страницы: 340

Moment SPH-M900

Бренд: Samsung Страницы: 224

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды