Avaya IP Ofice 8.0 Скачать руководство пользователя | Manualshive

Страница: 162 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 162

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

9.2.3 BRI Combination Card

This card is used to add a combination of ports to an IP500 V2 control unit. Not supported by IP500 control units.

·

Supports

·

10 voice compression channels. Codec support is G.711, G729a and
G.723 with 64ms echo cancellation. G.722 is supported by IP Office
Release 8.0 and higher.

·

6 Digital Station ports for

digital stations

(except 3800, 4100,

4400, 7400, M and T-Series).

·

2 Analog Extension ports.

·

2 BRI Trunk ports (4 BRI channels).

·

10 voice compression channels. Codec support is G.711, G729a and
G.723 with 64ms echo cancellation. G.722 is supported by IP Office
Release 8.0 and higher.

·

IP500 Control Unit:

·

IP500 V2 Control Unit:

·

Maximum per Control Unit: 2 combination cards of any type.

·

IP Office Basic Edition - Quick Mode mode systems are limited to a
maximum of 12 BRI channels.

·

IP500 Trunk Card Support:

1. The trunk daughter card is pre-

installed and cannot be replaced with another card type.

Port Type

Ports

Features

Digit Station

1 to 6

Provides

DS

ports for

digital stations

(except 4100, 4400, 7400, M and T-Series).

LEDs

·

Green On = Phone detected.

·

LED1 is also used for base card status:

·

Red On = Error

·

Red Slow Flash = Initializing.

·

Red Flash every 5 seconds = Card okay.

·

Red Fast Flash = System shutdown.

Analog
Extension

7 to 8

·

Supports ICLID modes DTMFA, DTMFC, DTMFD, FSK and UK20.

·

REN 2 (1 for external bell device).

·

Off-Hook current: 25mA

·

Ring Voltage: 40V.

·

Intended for connection to two-wire analog phones, the ports do not include a ringing
capacitor. For connection to 4-wire analog phones, connection should be via a master
socket with ringing capacitors.

·

No status LEDs are used for analog phone extensions.

BRI Trunk

9 to 10

·

Each trunk port supports 2B+D channels.

·

ETSI or AusTS013 basic rate protocol set through the IP Office configuration.

LEDs

·

Off = No trunk present.

·

Green on = Trunk present.

·

Green flashing = Trunk in use.

·

LED 9 is also used for daughter card status.

·

Red On = Error

·

Red Slow Flash = Initializing.

·

Red Flash every 5 seconds = Card okay.

·

Red Fast Flash = System shutdown.

Not Used

11 to 12

–

Name

Description

SAP Code

IPO IP500 V2 COMBINATION
CARD BRI

IPO IP500 V2 COMBINATION CARD BRI

700476021

32

224

32

«
...
160
161
162
163
164
...
»

Содержание IP Ofice 8.0

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IP Ofice 8.0

Бренд: Samsung Страницы: 123

SCH-R350 Series

Бренд: Samsung Страницы: 140

Бренд: Samsung Страницы: 138

Бренд: Samsung Страницы: 150

Бренд: Samsung Страницы: 72

Бренд: Samsung Страницы: 326

SGH C417 - Cell Phone - AT&T

Бренд: Samsung Страницы: 114

Бренд: Samsung Страницы: 136

SCH-R730 series

Бренд: Samsung Страницы: 134

Бренд: Samsung Страницы: 190

Бренд: Samsung Страницы: 34

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 186

SGH E250 - Cell Phone 13 MB

Бренд: Samsung Страницы: 12

Бренд: Samsung Страницы: 185

Бренд: Samsung Страницы: 2

Бренд: myPhone Страницы: 41

Бренд: Nortel Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды