Avaya IP Ofice 8.0 Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 136

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

Card Specification

Non-Avaya cards can be used in the Optional SD slot as long as they match or exceed the standard below:

·

SDHC 4GB minimum Class 2+. Single partition FAT32 format.

SD Card Folders

The System SD card contains the following folders:

·

/primary
Contains the firmware files for the IP Office control unit, external expansion modules and
supported phones. The folder can also contain music on hold files and license key files. This is the
main set of files used by the IP Office system when booting up. Also contains the stored copy of
the IP Office configuration.

·

/backup
Contains a copy of the primary folder at some previous point. A backup copy of the primary
contents to this folder can be invoked manually (using Manager or SSA) or as part of the IP Office
software upgrade using Manager.

·

/lvmail
Contains the system prompts used by Embedded Voicemail. Note that the mailbox messages and
greetings are stored in a sub-folder of the /dynamic folder.

·

The sub-folder /AAG is used to store Embedded Voicemail auto-attendant greetings.

·

/doc
Contains initial installation documentation for the system.

·

/dynamic
Contains files used by the IP Office and retained through a reboot of the IP Office system.

·

The sub-folder /lvmail is used to store individual user and group mailbox messages, name
recordings and announcements. The storage capacity for Embedded Voicemail is limited to 15
hours regardless of the capacity of the card.

·

/temp
Contains temporary files used by the IP Office and not retained through a reboot of the IP Office
system.

The Optional SD card can contain a similar set of folders. These are used as an additional backup or they can be used as
the source for upgrading the contents of the System SD card.

«
...
134
135
136
137
138
...
»

Содержание IP Ofice 8.0

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IP Ofice 8.0

Бренд: TCL Страницы: 35

Бренд: Pantech Страницы: 126

Бренд: 101VOICE Страницы: 2

Бренд: Xblue Networks Страницы: 98

Dusk2Dawn 2100-CD9 Series

Бренд: Rath Страницы: 8

Бренд: T-Mobile Страницы: 191

Бренд: NEC Страницы: 61

Бренд: T-Mobile Страницы: 211

Бренд: RATH MICROTECH Страницы: 2

Бренд: Infinix Страницы: 11

Бренд: Tadiran Telecom Страницы: 11

One Touch Scribe easy 8000A

Бренд: Alcatel Страницы: 23

Бренд: HTC Страницы: 139

Бренд: Blu Страницы: 31

A99-WMTA3030-01

Бренд: Westell Страницы: 12

Бренд: Gigo Страницы: 22

Бренд: 3Skypephone Страницы: 36

Бренд: Tobii Dynavox Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды