Avaya IP Ofice 8.0 Скачать руководство пользователя | Manualshive

Страница: 12 / 256

background image

IP Office Basic Edition - Quick Mode Installation

Page 12

15-601042 Issue 24i (20 December 2011)

IP Office 8.0

1.1.1 Overall Capacity

The following table is a summary only. The exact combinations of extension, trunk and user ports will also depend on local
variations in hardware supported.

IP Office

Basic Edition

- PARTNER®

Mode

IP Office

Basic Edition

- Norstar

Mode

IP Office

Basic Edition

- Quick Mode

IP Office

Essential

Edition

Extensions

Maximum Extensions

100

[1]

100

[1]

100

[1]

384

Trunks

Maximum Trunks

64

64

64

[5]

- Maximum Analog Trunks

32

32

32

204

- Maximum BRI Channels

[3]

–

12

12

32

- Maximum PRI Channels

[4]

24

30

30

240

- Maximum SIP Channels

[2]

20

20

20

[5]

- Maximum H323 IP Channels

–

–

–

[5]

1. 100 Extension in 3-digit extension numbering mode only. 48 extensions in 2-digit extension numbering mode.

·

In non-IP Office Essential Edition the system assumes that the base control unit is always fully populated with
up to 32 extensions, either real or phantom or a mix, to which it assigns extension numbers in sequence. It
does this before assigning extension numbers to any real extensions on attached external expansion modules
up to the system extension limit. If the system extension limit has not been exceeded, any remaining
extension numbers are assigned to additional phantom extensions.

2. Non-IP Office Essential Edition systems support 3 SIP channels without licenses. Additional channels up to the limit

require licenses. IP Office Essential Edition systems require licenses for all channels. In all modes, voice
compression hardware resources are also required for SIP support.

3. Non-IP Office Essential Edition systems do not support both BRI and PRI trunks in the same system.IP Office

Essential Edition systems support both BRI and PRI trunks in the same system. Non-IP Office Essential Edition
systems are restricted to 12 BRI channels regardless of the BRI hardware installed.

4. Non-IP Office Essential Edition systems are to 1 single-port PRI card.

5. Capacity is dependent on licenses, voice compression resources and available bandwidth.

«
...
10
11
12
13
14
...
»

Содержание IP Ofice 8.0

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IP Ofice 8.0

Бренд: D-Link Страницы: 56

Бренд: Eads Telecom Страницы: 2

Бренд: Olympia Страницы: 52

Solstice II SGH-A817

Бренд: Samsung Страницы: 199

Бренд: Samsung Страницы: 192

Бренд: Samsung Страницы: 193

Бренд: Samsung Страницы: 2

Бренд: Unitech Страницы: 2

Бренд: Hanlong Страницы: 60

Бренд: AEI COMMUNICATIONS Страницы: 5

OneTouch X1 7053D

Бренд: Alcatel Страницы: 20

Бренд: Blackberry Страницы: 6

myTouch myTouch 3G

Бренд: T-Mobile Страницы: 113

Бренд: Watchguard Страницы: 12

Бренд: Avaya Страницы: 6

Бренд: ATCOM Страницы: 60

HANDLEPLUS 326I GSM

Бренд: Doro Страницы: 280

Бренд: Hanlong Страницы: 149

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды