Astell AMA240 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 61

Astell AMA240 Скачать руководство пользователя страница 45

45

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

MANUAL UNLOCKING

Sizes 60 litres and below

Picture A

Picture B

Picture C

Picture A

Undo handle

• Loosen the screw at side of handle using an Allen key.

• Remove handle cover

Gently prise off the plastic cover surrounding the base
of the handle.

• Remove handle retainers

Undo the 4 screws holding the d- shaped plastic
handle retainers to the cover.
Separate the two d-shaped parts.

• Remove handle

Pull the handle off the square shaft.
Note the orientation to make refitting easier.
This will expose the unlocking hole beside the handle
shaft.

Picture B

Unlocking tool

You can use a long thin screwdriver - with a blade 3mm x
150mm long.

Picture C

This picture shows the top cover as if it was semi-
transparent.

• Insert tool

Hold the tool at the angle shown. Insert it carefully into
the hole, holding it straight so that it points toward the
front edge of the door.

«
...
43
44
45
46
47
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов