Astell AMA240 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 61

Astell AMA240 Скачать руководство пользователя страница 11

11

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

OPERATING
INSTRUCTIONS

The following sections provide operating instructions in
both a fully detailed version and short-form which can be
copied and fixed to the wall near to the steriliser.

Full details of the program entry procedure and further
technical details are provided in a separate programming
manual.

Other options such as the RS232 communications option
are detailed in separate instruction manuals.

Information on approved use

This equipment is not designed for use other than as a
medical steam steriliser for use within the temperature
and pressure ratings of the chamber design. It is intended
for use by a health care provider to sterilise medical
products by means of pressurized steam.

Never use the autoclave to sterilize corrosive products,
such as: acids, bases and phenols, volatile compounds
or solutions such as ethanol, methanol, chloroform or
radioactive substances.

Any alternative use or method of operation not covered
and specified within this and associated programming
manuals is specifically excluded and may be hazardous.
The manufacturer does not approve such alternative use
and under no circumstances will the manufacturer or his
agents accept responsibility for loss, damage, or injury,
consequential or otherwise, as a result of such alternative
use.

The manufacturer reserves the right in certain cases,
to reassess and/or amend the design or specification,
and provide individual written instructions detailing an
alternative use that is considered acceptable.

Astell Scientific and approved agents are able to offer
advice and assistance in setting up and commissioning
this steriliser. Please consult Astell Scientific or an
approved agent if necessary.

SECURITY PASSWORDS

The system protects from unauthorised use by security
password codes.

Factory set numbers

• OPERATOR

111111

• SUPERVISOR

222222

• SITE ENGINEER 333333

If in doubt consult your supplier.

Passwords for Astell engineer access and above are
available to suitably approved engineers on request.

Astell advises to change passwords after installation.

«
...
9
10
11
12
13
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов