Astell AMA240 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 61

Astell AMA240 Скачать руководство пользователя страница 40

40

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

OPTIONAL PRINTERS

PRINTER INDEPENDENCE

Please note that the fitted printer is not independent from
the controller and has no separate sensors or intelligence.
It records from the control sensors and prints the same
data as available on the display.

If your QA requirements dictate that the printer must
give a totally independent record of measurements
please consult your agent or Astell Scientific. A range of
independent printing solutions are available that work
together with these models.

Printers available

• Internal standard printer option.

Please see instructions below.

• Externalprinter option.

Please see separate manual for external printer option.

• External user-supplied RS232.

Please see separate manual for RS232 communications
option.

INTERNAL PRINTER OPTION

The standard printer supplied is the Astell type MPP537X.
This is a 40 character dot-matrix impact printer which
prints on 58mm wide plain roll paper. It uses a replaceable
ink ribbon cartridge and prints in one single colour (black).

Top load models

The printer is mounted in the front face of the machine.

Frontload models

The printer is mounted in the top cover.

Installing Replacement paper

• Open the front panel

• Remove the empty paper centre roll tube of the old

paper roll

• Slide the new roll over the paper roll support until it is

held by the clips

• Cut off the end of the paper cleanly with scissors

• Feed the cut edge of paper up into the printer

mechanism and operate the paper feed button.

Cut off the end of the paper cleanly with scissors

Feed the cut edge of paper into the mechanism and operate
the paper feed button

«
...
38
39
40
41
42
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов