Astell AMA240 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 61

Astell AMA240 Скачать руководство пользователя страница 18

18

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

STARTING A CYCLE

The chamber door must be closed and locked!

Select the chosen cycle (as above).
Press button to start cycle.

Delayed start option

If delayed start is not selected in settings the cycle starts
immediately (see next page).

For each of the time or date figures you wish to change
touch the figure on the screen e.g. to change the day:

Type the value you want using the numeric keys, then

press

. When you are happy with the date and time

shown press the clock button to save the changes.

When the elapsed time is up, the system will go directly
to start.

Delayed start safety

If anything happens that could affect the safety of the unit,
including the case of power failure, it will exit the delay
start countdown automatically.

Manual override

Immediate manual start

• Press the Cycle Start button

Cancel delayed start

• Press

• Select

• Login with password

• Select with up and down arrows

• Press Continue

• Answer the “are you sure” question

• To start select stage

• To cancel select cooling

«
...
16
17
18
19
20
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов