Astell AMA240 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 61

Astell AMA240 Скачать руководство пользователя страница 21

21

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

SECURITY ACCESS AND
PASSWORDS

The security system splits the users of this machine into
the following groups:

• OPERATORS

• SUPERVISORS

• SITE ENGINEERS

In each group there can be several individuals each
known by name, and each with a different security
password number.

ENTERING PASSWORDS

• Press the menu button for main menu

• Select settings menu

• Select edit passwords

• Now you have to log in with your password

• Touch your name or if you are a supervisor or higher

level touch the “next” button to display the other
groups

• Touch your user name. This takes you to the password

entry screens

Password entry screens

• Touch on the passwords bar

• Type your password. Enter 6 characters followed by

“CONTINUE”

Note:

If you enter the incorrect password you are

returned to the Main Menu.

«
...
19
20
21
22
23
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов