Astell AMA240 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 61

Astell AMA240 Скачать руководство пользователя страница 15

15

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

INITIAL POWER UP

Make sure the power supply is turned on.

During power-up, the screen shows the booting process
as the software loads, with a message “booting”, then the
Astell logo is displayed.

The system then goes to the operating screen.

BUTTONS AND DISPLAYS

Below are a selection of the buttons and displays that you
will see on the touchscreen in normal use. Full details -
see later in this manual.

Door open button

Press to unlock door

Alarm button

Display all system alarms.

Note:

This button flashes red if an alarm is activated. After

the alarm icon has been touched, the Password is used to
cancel alarms.

Password screen

Allows the supervisor to enter their password.

Menu button

Takes you to the next menu.

Return button

Return from selected screens back to the start screen.

Up and down buttons

Move up and down through lists e.g. to select a cycle.

Cycle counter

This counter is displayed on various screens and indicates
how many cycles the autoclave has run. This is not re-
settable.

Cycle Time

Time into current cycle
Stage Time - Elapsed time in Stage

The temperature and pressure

Channels selected are displayed:

Date and Time

Top right corner of the screen.

Alphanumeric keyboard

«
...
13
14
15
16
17
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов