Astell AMA240 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 61

Astell AMA240 Скачать руководство пользователя страница 22

22

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

TO CHANGE YOUR PASSWORD

• Log in as described above

• Press change your passwords

Select your group if required and your name, to get to the
enter password screen.

• Enter your current password

• Then enter your new password

• Touch the password bar

• Key in the required password

• Press “CONTINUE”

• Confirm the new password when asked

• Press “CONTINUE”

Invalid passwords

• You cannot use the same password as you used before

• You cannot use The same password as another user

TO CHANGE / ADD USER NAME

SUPERVISORS
SITE ENGINEERS
ASTELL ENGINEERS
DEVELOPERS

The passwords and names for all levels of users are
added and edited in the same way.

You can only change the security settings of a user who is
at a lower level of access than you are.

Supervisors can change operators codes.
Site engineers can change supervisors and operators
codes.
Astell engineers can change the site engineers,
supervisors and operators codes.
Developers can change all codes.

• Log in as a supervisor or higher using an appropriate

password

«
...
20
21
22
23
24
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов