Astell AMA240 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 61

Astell AMA240 Скачать руководство пользователя страница 16

16

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

DOOR CONTROLS

OPEN

Touch the “closed door” button on the display screen to
unlock the door. Then rotate the door handle clockwise to
disengage the door bolts and open the door.

The screen icon will change to Door open:

If “closed door” button does not show on screen then the
system will not allow you to open the door.

This is not possible or unsafe at this stage

The door will open only if the safety conditions are all
satisfied and no alarms are present.

HANDLE LOCKED WITH DOOR OPEN

If the door is open and you move the handle accidentally
to the locked position it will lock in that position.

To restore normal operation

Press the [DOOR] button to unlock

Then rotate the handle to the unlocked position.

CLOSE

Close the door

The icon will change to “Door closed”

Then rotate the door handle anti-clockwise to engage the
door bolts and secure the door.

Note:

Do not lean on the handle or hang anything over

the handle as this will cause the bolt to stick and will cause
early failure of the mechanism.

«
...
14
15
16
17
18
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов