Astell AMA240 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 61

Astell AMA240 Скачать руководство пользователя страница 17

17

Astell Autoclaves/Sterilisers – AMB220 | AMB230 | AMB240 | AMB420 | AMB430 | AMB440 | AMA240 | AMA440

SELECTING A PROGRAM

(Note - temperatures and times etc. will probably be
different to the examples shown here).

Press “SELECT CYCLE” button

This will take you to a screen where you can select any
one of the available programs.

Then touch the name of the selected cycle.

The display changes to show that a cycle has been
selected and loaded

Cycle Selected

Changes colour to show cycle selected.

Change cycle

If you wish to select another Cycle press
the “FOLDER” button, then select a
different

cycle.

WARNING!

The next press on the cycle button will
start the cycle!

IMPORTANT

The names, numbers and types of program
cycles available depend on the machine
specification, and what has been set up on the
machine.

This manual shows examples only and cycle
displays will not be exactly the same as shown
your machine.

«
...
15
16
17
18
19
...
»

Содержание AMA240






























































Отзывы:

Нет отзывов