Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 18 / 132

General safety instructions

Order number and explanation

Warning pictograms

MD 078

Risk of crushing of fingers/hand by accessi-
ble, moving parts of the machine!

This danger can cause extremely serious injuries
resulting in the loss of limbs.

Never reach into the danger area when the trac-
tor engine is running with the PTO shaft or hy-
draulic/electrical system connected.

MD 079

Risk of materials or foreign objects being
flung away by or out of the machine!

These dangers can cause extremely serious and
potentially fatal injuries.

•

Keep a sufficient safety distance from the
machine as long as the tractor engine is
running.

•

Ensure that all other persons also keep a
sufficient safety distance from the danger
area of the machine as long as the tractor
engine is running.

MD 082

Danger of falling from treads and platforms
when riding on the machine.

This danger causes serious or potentially fatal
injuries anywhere on the body.

It is forbidden to ride on the machine and/or
climb the machine while it is running. This also
applies to machines with treads or platforms.

Make sure that nobody is riding on the machine.

MD 084

Risk of crushing the entire body due to
standing in the swivel range when machine
parts are being lowered.

This can cause extremely serious and potentially
fatal injuries.

•

It is forbidden to stand in the swivel range of
the machine when machine parts are being
lowered.

•

Instruct personnel to leave the swivel range
of any machine parts which can be lowered
before you lower the parts.

Ceus-2TX BAG0183.2 01.19

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды