Barreto 1320H Manual Download | Manualshive

Page: 1 / 10

background image

1320 owners manual.doc

4/22/08

page 1 of 10

THE

MODELS 1320H & 1620B

HYDRAULIC REAR TINE TILLERS

CONGRATULATIONS!

You are now the proud owner of the BARRETO Model 1320 or 1620 tiller. Please take a
moment of your time to look over the following information. Familiarize yourself with the tiller,
its characteristics, and method of operation. Pay particular attention to the safety and operating
instructions.

If you have any questions or need any replacement parts in the future, please contact us at your
convenience. Our toll-free phone number, fax and email are listed below.

THANK YOU for your patronage and confidence in BARRETO equipment.

Barreto Manufacturing, Inc.

Innovative Equipment Engineered to Last

66498 Hwy 203, La Grande, OR 97850

(800) 525-7348 (541) 963-7348

FAX (541) 963-6755

E-Mail:

[email protected]

Web Site:

http://www.barretomfg.com

1
2
3
...
»

Summary of Contents for 1320H











Reviews:

No comments

Related manuals for 1320H

Brand: WaterLogic Pages: 16

Brand: Bard Pages: 29

Brand: EarthQuake Pages: 24

Brand: EarthQuake Pages: 28

Brand: White Outdoor Pages: 22

Brand: Zimmer Pages: 38

Brand: Poulan Pro Pages: 22

SUNJOE TJ603E-RM

Brand: SNOWJOE Pages: 15

Brand: Delfield Pages: 40

Brand: Draper Pages: 13

Brand: Draper Pages: 24

SkyAir RZF-A Series

Brand: Daikin Pages: 213

Brand: McCulloch Pages: 24

Brand: Robur Pages: 44

Brand: Chapman Pages: 11

Brand: Troy-Bilt Pages: 32

Brand: Nakayama Pages: 11

Brand: Raider Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands