Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 73 / 132

Commissioning

6.1.2

Requirements for tractor operation with attached machines

WARNING

Risk of breakage during operation of components through unap-
proved combinations of connecting equipment!

•

Ensure:

that the connection fittings on the tractor possess sufficient
permissible support capability for the drawbar load actually
present.

that the axle loads and weights of the tractor altered by the
drawbar load are within the approved limits. If necessary,
weigh them.

that the tractor's actual static rear axle load does not ex-
ceed the permissible rear axle load.

that the permissible total weight of the tractor is observed.

that the approved load capacities of the tractor tyres are not
exceeded.

Ceus-2TX BAG0183.2 01.19

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды