Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 82 / 132

Adjustments

WARNING

Risk of contusions, cutting, catching, drawing in and knocks
through

•

unintentional falling of the machine raised using the trac-
tor's three-point hydraulic system.

•

unintentional falling of raised, unsecured machine parts.

•

unintentional start-up and rolling of the tractor-machine
combination.

Secure the tractor and the machine against unintentional start-up and
rolling before making adjustments to the machine. See page 78.

8.1

Performing mechanical adjustments using an adjustment spindle

Depending on the equipment, different settings on the implement can
be made by adjusting a threaded spindle.

Adjusting the spindle using the ratchet

1. Remove the linch pin (3).

2. Engage the turning lever (2) in the required

direction.

3. Use the hand lever (1) to lengthen or short-

en the spindle.

4. Secure the adjustment using the linch pin

(3).

5. Rest the hand lever in parking position on

the frame and secure with a linch pin.

The scale (4) serves for orientation during ad-
justment.

Parking position for the hand lever

Ceus-2TX BAG0183.2 01.19

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды