Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 30 / 132

General safety instructions

2.16.7 Cleaning, maintenance and repairs

•

Repair-, maintenance- and cleaning operations as well as the
remedy of function faults should principally be conducted with

the drive is switched off

the tractor engine is at a standstill

the ignition key has been removed

the connector to the machine has been disconnected from
the on-board computer

•

Regularly check the nuts and bolts for a firm seat and retighten
them as necessary.

•

Before carrying out any maintenance-, repair- and cleaning work
ensure the lifted implement or lifted implement parts against un-
intended lowering.

•

When replacing work tools with blades, use suitable tools and
gloves.

•

Dispose of oils, greases and filters in the appropriate way.

•

Disconnect the cable to the tractor generator and battery, before
carrying out electrical welding work on the tractor and on at-
tached machines.

•

Spare parts must meet at least the specified technical require-
ments of AMAZONEN-WERKE! This is ensured through the use
of AMAZONE original spare parts!

Ceus-2TX BAG0183.2 01.19

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды