Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 117 / 132

Cleaning, maintenance and repairs

Draining the air reservoir

Drain the air reservoir every day.

1. Run the tractor engine (approx. 3 mins.)

until the compressed air tank has filled.

2. Switch off the tractor engine, apply the

handbrake and remove the ignition key.

3. Pull the drainage valve (1) in a sideways

direction by the ring until no more water es-
capes from the compressed air tank.

4. If the escaping water is dirty, let off air, un-

screw the drainage valve from the com-
pressed air tank and clean the compressed
air tank.

The compressed air tank must not

•

move around in the tensioning belts

•

be damaged

•

show any outward signs of corrosion dam-
age

The rating plate must not

•

show signs of corrosion

•

be loose

•

be missing

Replace the compressed air tank
(workshop), if one of the above-stated
points applies!

Ceus-2TX BAG0183.2 01.19

117

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды