Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 58 / 132

Structure and function

5.9

Rear harrow (optional)

The rear harrow is used to crumble and level the
soil.

The working intensity can be adjusted by insert-
ing the pins into different holes.

Secure the pin with a linch pin.

(1) Positioning pin for adjusting the working

intensity.

→

Peg the positioning pin so that the harrow is
resting and can swing freely to the rear.

(2) Position of the positioning pin to lock the

exact following harrow during road
transport.

(3) Install the road safety bar for road transport.

(4) Depending on the harrow system, adjust

the harrow height so that it is free of play

•

Make the same adjustments on all of the setting points.

•

Raise and peg the harrow to take it out of operation.

•

Attach the transport safety bars on the roller during operation.

Harrow system 12-125 Hi

For rollers: SW520, SW600, PW600, KW580,
RW600, UW580

Harrow system KWM650-125 Hi

For roller: KWM650

Ceus-2TX BAG0183.2 01.19

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды