background image

 

 

 

General safety instructions 

 

 

2.16.2 

Hydraulic system 

 

 

The hydraulic system is under a high pressure. 

 

Ensure that the hydraulic hose lines are connected correctly. 

 

When connecting the hydraulic hose lines, ensure that the hy-
draulic system is depressurised on both the machine and tractor 
sides. 

 

It is forbidden to block the operator controls on the tractor which 
are used for hydraulic and electrical movements of components, 
e.g. folding, swivelling and pushing movements. The movement 
must stop automatically when you release the appropriate con-
trol. This does not apply to equipment movements that: 

ο

 

are continuous or 

ο

 

are automatically locked or 

ο

 

necessarily require an open centre or pressure position to 
operate correctly 

 

Before working on the hydraulic system 

ο

 

Lower the machine 

ο

 

Depressurise the hydraulic system 

ο

 

Switch off the tractor engine 

ο

 

Apply the parking brake 

ο

 

Take out the ignition key 

 

Have the hydraulic hose line checked at least once a year by a 
specialist for proper functioning. 

 

Replace the hydraulic hose line if it is damaged or worn. Only 
use AMAZONE original hydraulic hose lines. 

 

The hydraulic hose lines should not be used for longer than six 
years, including any storage time of maximum two years. Even 
with proper storage and approved use, hoses and hose connec-
tions are subject to natural ageing, thus limiting the length of 
use. However, it may be possible to specify the length of use 
from experience values, in particular when taking the risk poten-
tial into account. In the case of hoses and hose connections 
made from thermoplastics, other guide values may be decisive. 

 

Never attempt to plug leaks in hydraulic lines using your hand or 
fingers. 

 

  Escaping high pressure fluid (hydraulic fluid) may pass through 

the skin and ingress into the body, causing serious injuries!  

 

  If you are injured by hydraulic fluid, contact a doctor immediately. 

Danger of infection. 

 

When searching for leak points, use suitable aids, to avoid the 
serious risk of infection. 

 

26 

 

Ceus-2TX  BAG0183.2  01.19

 

 

Содержание Ceus 4000-2TX





































































































































Отзывы: