Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 103 / 132

Cleaning, maintenance and repairs

12.1

Cleaning

•

Pay particular attention to the brake, air and hydraulic hoses!

•

Never treat brake, air and hydraulic hoses with petrol, benzene,
petroleum or mineral oils.

•

After cleaning, grease the machine, in particular after cleaning
with a high pressure cleaner/steam jet or liposoluble agents.

•

Observe the statutory requirement for the handling and removal
of cleaning agents.

Cleaning by using a high pressure cleaner / steam jet

•

Always observe the following points when using a high pressure
cleaner/steam jet for cleaning:

Do not clean any electrical components.

Do not clean any chrome-plated components.

Never aim the cleaning jet of the cleaning nozzle of the
high pressure cleaner/steam jet directly at lubrication
points, bearings, rating plates, warning signs, and stickers.

Always maintain a minimum jet distance of 300 mm be-
tween the high pressure or steam jet cleaning nozzle and
the machine.

The set pressure of the high-pressure cleaner/steam jet
must not exceed 120 bar.

Comply with the safety regulations when working with high
pressure cleaners.

Ceus-2TX BAG0183.2 01.19

103

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды