Amazone Ceus 4000-2TX Скачать руководство пользователя | Manualshive

Страница: 116 / 132

background image

Cleaning, maintenance and repairs

Brake pad check

To check the brake pad thickness, open the in-
spection hole (1) by opening the rubber tab.

Changing the brake pads

→

Workshop work

Criterion for changing the brake pads:

•

Minimum pad thickness of 5 mm was
reached.

•

Wear edge (2) was reached.

Adjusting the linkage adjuster

Move the linkage adjuster by hand in the pres-
sure direction. If the free travel of the long-stroke
diaphragm cylinder pressure rod is max. 35 mm,
the wheel brake must be readjusted.

Adjustments are made using the readjustment
hexagon bolt on the linkage adjuster. Set the free
travel "a" to 10-12 % of the connected brake
lever length "B",
e.g. lever length 150 mm = free travel 1
5 – 18 mm.

Checking the function of the automatic slack adjuster

1. Secure the machine against rolling away

and release the service brake and parking
brake.

2. Manually actuate the slack adjuster.

The free travel (a) may be a maximum of 10-
15% of the connected brake lever length (B) (e.g.
brake lever length 150 mm = free travel 15 – 22
mm).

Readjust the slack adjuster if the free travel is
outside of the tolerance.

→

Workshop work

116

Ceus-2TX BAG0183.2 01.19

«
...
114
115
116
117
118
...
»

Содержание Ceus 4000-2TX





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ceus 4000-2TX

Бренд: Ryobi Страницы: 22

Бренд: York Страницы: 230

Бренд: Daikin Страницы: 34

Бренд: Tracmaster Страницы: 2

Бренд: Amazone Страницы: 84

Бренд: Fieldmann Страницы: 27

644H-Bronco, 645A-Bronco

Бренд: Troy-Bilt Страницы: 26

Бренд: EarthWise Страницы: 42

Бренд: ATC Страницы: 21

Бренд: Clima-Flex Страницы: 24

Бренд: Scheppach Страницы: 56

Бренд: UNIA Страницы: 34

Бренд: Ozito Страницы: 8

Бренд: Ozito Страницы: 8

Бренд: Daewoo Страницы: 15

Бренд: Raider Страницы: 78

Бренд: Gardena Страницы: 12

Бренд: Daikin Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды