Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 45 / 132

Structure and function

Line filter in the coupling head with sealing sur-
faces, O-ring and filter

(1) Air reservoir

(2) Test connection

(3) Drainage valve for condensate

5.1.1

Coupling the brake and supply lines

WARNING

Risk of contusions, cuts, dragging, catching or knocks from
incorrectly functioning brake system.

•

When coupling the brake and supply line, ensure that:

the coupling head seals are clean.

the sealing rings of the hose couplings form a proper seal.

•

Always replace damaged seals immediately.

•

Drain the air tank before the first journey each day.

•

Only move off with the machine connected when the pressure
gauge on the tractor shows 5.0 bar.

WARNING

Risk of contusions, cuts, dragging, catching or knocks from
unintentionally rolling machine with the operating brake re-
leased!

Always couple the hose coupling of the brake line (yellow) first, fol-
lowed by the hose coupling of the supply line (red).

The operating brake of the machine moves out of the brake position
immediately the red hose coupling has been coupled.

Ceus-2TX BAG0183.2 01.19

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды