background image

 

 

 

 

Transportation 

 

Transportation 

 

 

During transportation, follow the instructions given in the section 
"Safety instructions for the operator", page 26. 

 

Before moving off, check: 

ο

 

that the supply lines are connected correctly. 

ο

 

the lighting system for damage, proper operation and 
cleanness, 

ο

 

the hydraulic systems visually for obvious defects 

ο

 

the bearing frame parts for damage. 

 

 

WARNING 

Risk of being crushed, cut, caught, drawn in or struck if the ma-
chine is unintentionally released from its attached or hitched 
position. 

Carry out a visual check that the lower link pins are firmly fixed with 
the lynch pin against unintentional release. 

 

 

WARNING 

Risk of contusions, cutting, catching, drawing in and knocks 
when making interventions in the machine through unintentional 
machine movements. 

 

Secure the machine against unintentional movements before 
starting transportation. 

 

 

WARNING 

Risk of contusions, cuts, dragging, catching or knocks from 
tipping and insufficient stability. 

 

Drive in such a way that you always have full control over the 
tractor with the attached machine. 

 

  In so doing, take your personal abilities into account, as well as 

the road, traffic, visibility and weather conditions, the driving 
characteristics of the tractor and the connected machine. 

 

Before transportation, fasten the side locking of the tractor lower 
link, so that the connected or coupled machine cannot swing 
back and forth. 

 

Ceus-2TX  BAG0183.2  01.19

 

93 

 

Содержание Ceus 4000-2TX





































































































































Отзывы: