Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 115 / 132

Cleaning, maintenance and repairs

Checking the play on wheel hub bearings

1. To check the play on wheel hub bearings,

raise the axle until the wheels turn freely.

2. Release the brake.

3. Place a lever between the tyre and the

ground and check the play.

If bearing play can be detected:

Adjust the bearing play

1. Remove the dust cup or hub cap.

2. Remove the split pin from the axle nut.

3. Tighten the wheel nut while turning the

wheel at the same time until the wheel hub
is lightly braked as it turns.

4. Turn axle nut back to the next available split

pin hole. To the next matching hole (max.
30°).

5. Fit split pin and bend slightly open.

6. Top up the dust cap with high melting point

grease and drive it into, or screw it onto the
wheel hub.

Ceus-2TX BAG0183.2 01.19

115

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды