Amazone Ceus 4000-2TX Скачать руководство пользователя

Страница: 100 / 132

Use of the machine

10.2

Operation

•

The machine is coupled to the tractor.

•

The machine is in working position.

•

Check the working position of the hydraulic drawbar

control.

•

When carrying out work, operate the tractor control unit

yellow

float position.

•

Avoid reversing when the machine is in working position!

10.3

Headland

Prior to turning on headlands:

•

Actuate the tractor control unit

yellow

→

Raise the implement.

After turning:

1. Actuate the tractor control unit

yellow

→

Lower the implement.

2. Switch the tractor control unit

yellow

to float position.

→

Work now continues.

Use at the headland only when the direction of the implement corre-
sponds to the direction of working.

100

Ceus-2TX BAG0183.2 01.19

Содержание Ceus 4000-2TX





































































































































Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды

Amazone Ceus 4000-2TX, Руководство по эксплуатации

Результаты поиска

Содержание Ceus 4000-2TX

Отзывы:

Похожие инструкции для Ceus 4000-2TX

Бренды по названию

Популярные бренды