Barreto 916 User'S Information Manual Download | Manualshive

Page: 1 / 9

background image

916 - 918 owners manual.doc

4/22/08

page 1 of 9

THE

MODEL 916/918

HYDRAULIC REAR TINE TILLER

CONGRATULATIONS!

You are now the proud owner of the BARRETO Model 916/918 tiller. Please take a moment of
your time to look over the following information. Familiarize yourself with the tiller, its
characteristics, and method of operation. Pay particular attention to the safety and operating
instructions.

If you have any questions or need any replacement parts in the future, please contact us at your
convenience. Our toll-free phone number, fax and email are listed below.

THANK YOU for your patronage and confidence in BARRETO equipment.

Barreto Manufacturing, Inc.

Innovative Equipment Engineered to Last

66498 Hwy 203, La Grande, OR 97850

(800) 525-7348 (541) 963-7348

FAX (541) 963-6755

E-Mail:

[email protected]

Web Site:

http://www.barretomfg.com

1
2
3
...
»

Summary of Contents for 916










Reviews:

No comments

Related manuals for 916

Brand: Daikin Pages: 16

Brand: AIREDALE Pages: 122

Brand: CRT Pages: 40

Brand: Yard Machines Pages: 24

Brand: Ozito Pages: 26

GT- 390 GT- 395

Brand: Gama Garden Pages: 13

Brand: lancer Pages: 28

Brand: Garland Pages: 172

MILLENNIUM 28971AR

Brand: York Pages: 104

EWAA011-016DAV3P

Brand: Daikin Pages: 20

Brand: GreenWorks Pages: 36

Brand: York Pages: 12

Brand: Poulan Pro Pages: 7

Brand: Poulan Pro Pages: 21

Brand: Poulan Pro Pages: 24

Brand: Murray Pages: 28

DOMINO BASIC Series

Brand: Thermocold Pages: 21

Econo-Horse 12185

Brand: Troy-Bilt Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands