Agilent Technologies G1314B Скачать руководство пользователя страница 44

Страница: 44 / 208

Agilent 1260 Infinity VWD User Manual

Installing the Detector

Ensure the line power switch at the front of the detector is OFF.

Figure 11

Front View of Detector

Connect the power cable to the power connector at the rear of the
detector.

Connect the CAN cable to other Agilent 1260 Infinity modules.

If a Agilent ChemStation is the controller, connect the LAN connection
to the LAN interface board in the detector.

Connect the analog cable (optional).

Connect the APG remote cable (optional) for non- Agilent 1260 Infinity
instruments.

HiVijh^cY^XVidg

\gZZc$nZaadl$gZY

A^cZedlZghl^iX]l^i]

\gZZca^\]i

N O T E

The figure above shows the flow cell already installed. The flow cell area is closed with a
cover. The flow cell has to be installed as described in

“Flow Connections to the

Detector”

on page 46.

N O T E

If an Agilent 1200 Infinity Series DAD/MWD/FLD is in the system, the LAN should be
connected to the DAD/MWD/FLD (due to higher data load).

Содержание G1314B

















































































































































































































Результаты поиска

Содержание G1314B

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G1314B, Руководство пользователя

Результаты поиска

Содержание G1314B

Отзывы:

Бренды по названию

Популярные бренды