manualshive.com logo in svg

Agilent Technologies G1314B, Руководство пользователя

Поделиться
Скачать
Agilent Technologies G1314B Скачать руководство пользователя страница 194

194

Agilent 1260 Infinity VWD User Manual

13

Appendix

General Safety Information

Safety Symbols

Table 27

Safety Symbols

Symbol

Description

The apparatus is marked with this symbol when the user should refer to 
the instruction manual in order to protect risk of harm to the operator and 
to protect the apparatus against damage.

Indicates dangerous voltages.

Indicates a protected ground terminal.

Indicates eye damage may result from directly viewing the light produced 
by the deuterium lamp used in this product.

The apparatus is marked with this symbol when hot surfaces are available 
and the user should not touch it when heated up.

WA R N I N G

A WARNING 

alerts you to situations that could cause physical injury or death.

➔

Do not proceed beyond a warning until you have fully understood and met the 
indicated conditions. 

C A U T I O N

A CAUTION 

alerts you to situations that could cause loss of data, or damage of equipment.

➔

Do not proceed beyond a caution until you have fully understood and met the 
indicated conditions.

Содержание G1314B

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды