ADVANTEST R3765AG Скачать руководство пользователя страница 327

Страница: 327 / 446

R3765/67G Series Network Analyzer Operation Manual

10.1 Preparing for a Performance Test

10-1

PERFORMANCE TEST

This chapter describes the test method to keep the performance of the R3765/67G series.

Contact ADVANTEST for other test methods than the items described in this chapter.

10.1 Preparing for a Performance Test

10.1.1 Warm up

Warm up the R3765/67G series for at least 30 minutes (pre-heating).
Also, warm up each calibration standards as well.

10.1.2 Preparing Measurement Instrument

The following measurement instruments are required referring to the test items listed in Table
10-1.

Table 10-1 Required Measurement Instrument for Performance Test (1 of 3)

Test items

Measurement Instrument

Remarks

Frequency
accuracy and
range

• Counter

Frequency

: 300kHz to 3.8GHz

(R3765G Series)
300kHz to 8.0GHz
(R3767G Series)

Display

: 7 digits or more

Accuracy

: 0.1ppm or less

R5372 (to 18GHz)
or R5373 (to 26GHz)
(ADVANTEST-made)

Refer to
section 10.2

• RF cable

BNC-BNC, N-N Type

• 50

Ω

to 75

Ω

conversion adapter

(when OPT 12 or 13 is installed)

11852 B
(Agilent
Technologies)

Output/input
level and
flatness

• Power meter

Frequency

: 300kHz to 8GHz

Power range : -21dBm to +17dBm

NRVS (R&S)
(Calibrated under the
national standard)

Refer to
section 10.3

• Power sensor

Frequency

: 300kHz to 8GHz

Power range : -21dBm to +17dBm

NRV - Z51(R&S)
(DC to 18GHz)

• Network analyzer

R3765/67CG
(ADVANTEST-made)

• 50

Ω

to 75

Ω

conversion adapter

(when OPT 12 or 13 is installed)

11852 B
(Agilent Technolo-
gies)

• 75

Ω

n-type through

(when OPT 12 or 13 is installed)

85036-60014
(Agilent Technolo-
gies)

Содержание R3765AG































































































































































































































































































































































































































































Результаты поиска

Содержание R3765AG

Отзывы:

Похожие инструкции для R3765AG

Бренды по названию

Популярные бренды

ADVANTEST R3765AG, Руководство по эксплуатации

Результаты поиска

Содержание R3765AG

Отзывы:

Похожие инструкции для R3765AG

Бренды по названию

Популярные бренды