ADVANTEST R3765AG Скачать руководство пользователя страница 284

Страница: 284 / 446

R3765/67G Series Network Analyzer Operation Manual

7.13 GPIB Block

7-140

(*3) The instrument is equipped with a compact flash disk as a memory device.

This disk is divided into multiple partitions, which are used depending on
applications.

C: This can be used freely. However, the registers used in the SAVE function

are created on the C drive; therefore, depending on how the SAVE registers
are used, the actual user capacity differs.

D: This is used to save files required for firmware. The contents of firmware

vary depending on the firmware version.

E: This drive is used exclusively for firmware. Writing data on this disk is

impossible.

7.13.2 GPIB Menu

The setting and the explanation

Press the [LCL] to call the GPIB menu. (Refer to section A.4.)

GPIB menu

{SYSTEM CONTROLLER} : Sets the R3765/67G series to the system controller.

{TALKER LISTENER}

: Sets the R3765/67G series to the talker/listener.

{SET ADDRESSES}

: Calls the address menu used for setting the GPIB

address. (See step

Address menu

{ADDRESS R3765G}

: Sets the GPIB address of the R3765/67G series. (Note)

{ADDRESS PLOTTER}

: Sets the GPIB address of the plotter.

{ADDRESS PRINTER}

: Sets the GPIB address of the printer.

Note:

R3767G is displayed for R3767G series.

Содержание R3765AG































































































































































































































































































































































































































































Результаты поиска

Содержание R3765AG

Отзывы:

Похожие инструкции для R3765AG

Бренды по названию

Популярные бренды

ADVANTEST R3765AG, Руководство по эксплуатации

Результаты поиска

Содержание R3765AG

Отзывы:

Похожие инструкции для R3765AG

Бренды по названию

Популярные бренды