ADVANTEST R3765AG Скачать руководство пользователя страница 313 | Manualshive

Страница: 313 / 446

background image

R3765/67G Series Network Analyzer Operation Manual

8.1 Inspection and Simple Troubleshooting

8-1

8

IN ABNORMALITIES

Read this chapter when the R3765/67G series becomes abnormal.

8.1

Inspection and Simple Troubleshooting

If the R3765/67G series becomes abnormal, check the following items before asking for repair.
When the trouble cannot be resolved by the following countermeasures, contact a sales
representative. The addresses and the phone numbers are mentioned at the end of this manual.
The fare will be charged on the user even for a repair as shown in the table below.

Symptom

Assumed cause

Remedy

The power cannot
be turned on.

Power cable is not surely
inserted in the connector.

Turn the power switch OFF, and re-
connect the power cable.

Power fuse is blown.

Replace power fuse.

No trace appears
on the screen.

BACK LIGHT is set to OFF.

Press the BACK LIGHT to switch
ON.

Input cable or connector is loose.

Re-connect the input cable or
connector.

Does not sweep.

Setting of the trigger is SINGLE.

Set to CONTINUOUS.

The measured
result is incorrect.

The calibration was not
performed correctly.

Execute the calibration meeting the
measurement.

Key does not work.

In GPIB remote control mode.

When a program is being executed,
stop it and press LCL key.

Data cannot be
read (recalled) from
floppy disk.

Floppy disk defect.

Check operation with other floppy
disk.

FDD (Floppy disk drive) defect.

Ask ADVANTEST for repair.

Not set to A:drive.

Set it to A:drive

Data cannot be
recorded (saved) in
floppy disk.

The floppy disk is not initialized.

Initialize the floppy disk.

The write protect is enabled.

Release the write protect.

Not set to A:drive.

Set it to A:drive.

«
...
311
312
313
314
315
...
»

Содержание R3765AG































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R3765AG

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

Бренд: DAKOTA ULTRASONICS Страницы: 25

Бренд: DAKOTA ULTRASONICS Страницы: 36

Бренд: FCI Страницы: 44

Бренд: FCI Страницы: 36

Бренд: FCI Страницы: 26

Бренд: TC Electronic Страницы: 20

Бренд: GARANT Страницы: 368

Бренд: Keeler Страницы: 68

Бренд: Rhosonics Страницы: 65

iTrans 77023554

Бренд: Industrial Scientific Страницы: 94

Бренд: Jaquet Страницы: 27

Бренд: Kirby Morgan Страницы: 101

Бренд: BASI Страницы: 69

Бренд: Vectronics Страницы: 28

AquiTron AT-WFM

Бренд: aquilar Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды