manualshive.com logo in svg

Yamato SM520, Instruction Manual, Page: 91 / 111

Share
Download
Yamato SM520 Instruction Manual Download Page 91

88 

6. Maintenance Method 

Daily Inspection and Maintenance 

 
For the safety use of this unit, please perform the daily inspection and maintenance without fail. 
 

Warning 

 

 

 

 

● 

Disconnect  the power  cable  from  the  power source  when doing an inspection  or maintenance 

unless needed. 

● 

Perform the daily inspection and maintenance after returning the temperature of this unit to the   

normal one. 

● 

Do not disassemble this unit. 

  caution   

 

 

● 

Use a well-drained soft cloth to wipe dirt on this unit. Do not use benzene, thinner or cleanser for 

wiping. Do not scrub this unit. Deformation, deterioration or color change may result in. 

 

Monthly maintenance 

● 

Check the earth leakage breaker function. 

1. Connect the power cord. 
2. Turn the breaker on. 
3. Push the red test switch by a ballpoint pen etc. 
4. If there is no problem, the earth leakage breaker will be turned 
off.

 

 

 

● 

Clean the silencer. 
The exhaust hose is equipped with a silencer on its end to 
reduce the noise generated daring air purge. 

1.  Remove  the  silence  and  wash  it  with  water.  It  contains  a 
backwater  prevention  ball.  Make  sure  not  lose  the  ball  when 
the silencer is removed. 
2. After cleaning, put the ball first into the silencer and then fix 
the silencer 
 

 

 

Filter cleaning 

  If  the  filter  on  the  bottom  of  chamber  is  clogged 

with dust or dirt, the equipment can not drain the 

water. Clean it appropriately as required. 

・

The filter is inserted in the drain outlet. Pull it out 

to sweep it. 

・

Insert it in place after cleaning. 

 

Cleaning inside the chamber 

  Use  soft  sponge  to  clean  inside  the  chamber  not  to  damage  the  surface  inside  the  chamber.   

Do not remove the filter on the bottom of chamber at cleaning. If it is removed, the pipe fitting is 

clogged with dirt inside the chamber. 

  The heater and sensor are provided on the bottom inside the chamber. Make sure not to bend 

or damage the filter. 

◆

For any questions, contact the dealer who you purchased this unit from, or the nearest sales division in our company.

Silencer 

Ball 

Summary of Contents for SM520
















































































































Reviews:

No comments