Yamato SM520 Instruction Manual Download Page 10 | Manualshive

Page: 10 / 111

Yamato SM520 Instruction Manual Download Page 10

7

2. Before Using

Installation precautions

3. Before/after installing

It may cause injure to a person if this unit falls down or moves by the earthquake and the
impact. etc..To prevent, take measures that the unit cannot fall down, and not install at busy
place.

4. Do not install the equipment near alarm device

The equipment releases large amount of vapor when the cover is opened just after the
operation is completed. Amlordingly, do not install the equipment on the site over which
electrical equipment especially an alarm device is provided over it.

5. Ventilate the equipment sufficiently

Do not block the heat releasing outlets on the side face and back face of equipment during
operation. The temperature inside the equipment rises, which may cause the deterioration or
failure of equipment, amlident, or fire disaster.

6. Do not use this unit in an area where there is flammable or explosive gas

Never use this unit in an area where there is flammable or explosive gas. This unit is not
explosion-proof. An arc may be generated when the power switch is turned ON or OFF, and
fire/explosion may result.
To know about flammable or explosive gas, refer to page 104

—14. List of Dangerous

Substances.

爆発性ガス

可燃性ガス

«
...
8
9
10
11
12
...
»

Summary of Contents for SM520
















































































































Reviews:

No comments