Yamato SM520 Instruction Manual Download Page 7 | Manualshive

Page: 7 / 111

Yamato SM520 Instruction Manual Download Page 7

4

1. Safety Precautions

Warning

・

Caution

Caution

When opening the cover...

Make  sure  that  the  pressure  of  equipment  has  decreased  to  0(zero)  MPa  before
opening  the  cover.  Generally  the  cover  does  not  open  due  to  the  safety  lock
mechanism  under  the  high  pressure  condition.  The  high-temperature  and  pressure
vapor blows out if the cover is forced open under high pressure, which may cause a
burn  injury.  A  large  amount  of  vapor  blows  out  from  inside  of  the  chamber  when
opening  the  cover  just  after  the  sterilizing  operation  has  completed  (when  the
temperature inside the chamber is high). Do not put your hands and face close to the
cover.

When draining water...

Make sure that the pressure of equipment has decreased to 0(zero) MPa before draining the
sterilizing water. The hot water blows out if the valve is opened under high pressure. The sterilizing
water remains very hot just after the sterilizing operation has completed even the pressure reading is
0(zero) MPa. Drain the water after it is sufficiently cooled down.

Do not touch the drain bottle during operation

A drain bottle, which contains hot water during and just after operation, is placed inside the door in
the front face of equipment. To avoid a burn injury, remove the bottle after the water is sufficiently
cooled down. Do not open the door during the operation of equipment.

Make sure to drain the water when the water level comes to the seal
position

The hot water or vapor may blow out from the drain bottle if the equipment is operated with too much
drain water (water level above the seal position). (Refer to 15

of “Preparation before operation” in

Page 13 for details.)

Securely fix the silicon plug of the drain bottle

Securely fix the silicon plug when installing the drain bottle. The hot water or vapor may blow out
from the drain bottle if the equipment is operated with the plug loosen. (Refer to 5

of “Preparation

before operation

” in Page

Error! Bookmark not defined.

for details.)

Do not touch the hot section

Some sections on the equipment such as the circumference of cover or drain bottle are very hot
during or just after the operation of equipment. Do not touch these sections to avoid burn injury.

«
...
5
6
7
8
9
...
»

Summary of Contents for SM520
















































































































Reviews:

No comments