Yamato SM520 Instruction Manual Download Page 15 | Manualshive

Page: 15 / 111

Yamato SM520 Instruction Manual Download Page 15

12

2. Before Using

Preparation before operation

(10)

Set the sterile samples



Set the samples to the chamber, putting them into the attached sample basket.



Put the sample or sterilization bag into the chamber so they should not block or cover the

sensor inside the chamber, exhaust outlet and end connection to pressure gauge. If they
are blocked or covered, the vapor cannot be discharged and the equipment cannot be
operated correctly. Do not spill the samples when taking them out from/putting them into
the chamber. The failure in piping system, bad smell or dirt may result in.



In case liquid such as medicinal solution or medium is sterilized, the amount of liquid

should be 60% or less of the capacity of container. They may be boiled over if too much
quantity is supplied.



Widely open the opening of sterilization bag when used. If it is closed, the samples are

insufficiently sterilized.

(11)

Close the door before operation



Make sure to close the door of equipment before operation. If the door is not fully closed,

the cooling water box may be touched and may cause a burn injury. Do not open the door
during operation.

(12)

Close the cover



Make sure that no foreign objects exist

on  the  packing  of  the  cover  and  its
contact area before closing  the cover.
If  any  foreign  object  exists,  the  vapor
may leak from the inside.

Turn the lock lever to the left to close the cover.

Turn the lock lever to the right to open the cover.

电源接通前不能开锁



Fully close the cover and slide the lock lever on the cover to the left side. If it is closed

inappropriately, the vapor blows out from the inside, which may cause a burn injury.



Do not press the hook and operate the lock lever for purposes other than maintenance of

equipment.

(13)

Attach the droplet tray



Attach the droplet tray to the equipment

to  prevent  the  water  drops  that  are
made  from  vapor  that  generate  during
air purge from dropping down from the
packing  onto  the  samples  or  onto  the
top  board.  Pour  off  the  droplets  inside
the tray periodically.

Droplet tray

Keep

locked

before

power on

«
...
13
14
15
16
17
...
»

Summary of Contents for SM520
















































































































Reviews:

No comments